MIG Welder Certification: Difference between revisions
(Add (most) current certification pages) |
(Increase all header levels in certifications by one) |
||
Line 3: | Line 3: | ||
To be certified to use the CMS’s MIG welding machines independently, the student must demonstrate an understanding of the following tool features, policies, and operational steps. | To be certified to use the CMS’s MIG welding machines independently, the student must demonstrate an understanding of the following tool features, policies, and operational steps. | ||
== Tool Anatomy == | === Tool Anatomy === | ||
* Parts of the MIG Welder are properly identified | * Parts of the MIG Welder are properly identified | ||
Line 15: | Line 15: | ||
** Tip holder | ** Tip holder | ||
== Gas Tank Safety == | === Gas Tank Safety === | ||
* Never move the gas tank without the cap on! | * Never move the gas tank without the cap on! | ||
== Materials == | === Materials === | ||
What materials may be welded with the CMS’s MIG welding machines? | What materials may be welded with the CMS’s MIG welding machines? | ||
Line 31: | Line 31: | ||
* Stainless Steel | * Stainless Steel | ||
== Pre-Operation == | === Pre-Operation === | ||
* Personal Protection Gear - safety glasses, welding helmet, welding gloves, welding jacket (or long sleeves!) | * Personal Protection Gear - safety glasses, welding helmet, welding gloves, welding jacket (or long sleeves!) | ||
Line 44: | Line 44: | ||
* Set the machine appropriately for the gauge of steel you will be welding, using the chart on the inside of the side panel. | * Set the machine appropriately for the gauge of steel you will be welding, using the chart on the inside of the side panel. | ||
== Operation == | === Operation === | ||
* Turn on the fume extractor and position the end of the extraction arm near your workpiece. | * Turn on the fume extractor and position the end of the extraction arm near your workpiece. | ||
Line 53: | Line 53: | ||
* Treat all work as if it is hot enough to burn you through your gloves. | * Treat all work as if it is hot enough to burn you through your gloves. | ||
== Post-Operation == | === Post-Operation === | ||
* Turn off the fume extractor. | * Turn off the fume extractor. | ||
Line 63: | Line 63: | ||
* Sweep up (the floor) after yourself. | * Sweep up (the floor) after yourself. | ||
== Lockout/Tagout Procedure == | === Lockout/Tagout Procedure === | ||
* Unplug the machine, coil the cord, and place the plug end in a safe/visible location. Fill out an “Out of Order” tag and post it on the machine. Notify the Metalshop Lead (and Desker, if on site). | * Unplug the machine, coil the cord, and place the plug end in a safe/visible location. Fill out an “Out of Order” tag and post it on the machine. Notify the Metalshop Lead (and Desker, if on site). | ||
== Questions == | === Questions === | ||
Who do you contact if you have questions about the CMS MIG welding machines? | Who do you contact if you have questions about the CMS MIG welding machines? |
Revision as of 16:50, 25 August 2020
MIG Welder Certification | |
---|---|
Version | 0.1.0 |
Approval Date | Draft/NOT APPROVED |
Prerequisites | |
Document/Printout | MIG Welder Certification |
Required For Tools/Shops |
Student: | |
---|---|
Trainer: | |
Date: | |
Version: | 0.1.0 - Draft/NOT APPROVED: DO NOT USE |
Certification required for: MIG Welder (Metal Shop)
DO NOT USE THIS PAGE AS A SIGN OFF SHEET
Please print the document from the download link in the top right of the wiki page instead!
Training Check-Off List:
To be certified to use the CMS’s MIG welding machines independently, the student must demonstrate an understanding of the following tool features, policies, and operational steps.
Tool Anatomy
- Parts of the MIG Welder are properly identified
- Pressure regulator
- Speed selector
- Voltage selector
- Ground clamp
- Gun
- Nozzle
- Contact Tip
- Tip holder
Gas Tank Safety
- Never move the gas tank without the cap on!
Materials
What materials may be welded with the CMS’s MIG welding machines?
- Clean Carbon Steel
What materials may be welded with the CMS’s MIG welding machines?
- Galvanized metals
- Aluminum
- Stainless Steel
Pre-Operation
- Personal Protection Gear - safety glasses, welding helmet, welding gloves, welding jacket (or long sleeves!)
- Do not wear clothing made from synthetic or synthetic blends.
- No unrestrained long hair and no flowing clothes. Closed-toed shoes are required.
- Make sure there are no puddles on the floor in welding area, particularly around machines and foot pedals.
- Make sure that the welding area is free of flammable materials.
- Adjust welding screens to make sure no bystanders can be caught by arc-flash.
- Regulator:
- Tank is opened 1/2 turn.
- Depress torch trigger to start the gas cycle, then adjust the flow-meter or regulator (if necessary). See individual machine pages for optimal settings.
- Set the machine appropriately for the gauge of steel you will be welding, using the chart on the inside of the side panel.
Operation
- Turn on the fume extractor and position the end of the extraction arm near your workpiece.
- Clip the wire electrode to within 1/4" of the end of the gas nozzle before starting a weld.
- Clean the gas lens and contact tip as needed.
- Replace the contact tip if you're experiencing wire feed problems and it is absolutely necessary.
- Hold the torch as appropriate to your weld position and requirements.
- Treat all work as if it is hot enough to burn you through your gloves.
Post-Operation
- Turn off the fume extractor.
- Turn off the machine (MIG welder).
- Turn off the gas using the large valve on the cylinder.
- Disconnect the ground clamp, coil cords and store neatly.
- Return all tools.
- Clean the workbench.
- Sweep up (the floor) after yourself.
Lockout/Tagout Procedure
- Unplug the machine, coil the cord, and place the plug end in a safe/visible location. Fill out an “Out of Order” tag and post it on the machine. Notify the Metalshop Lead (and Desker, if on site).
Questions
Who do you contact if you have questions about the CMS MIG welding machines?
- The CMS Metalshop Leads, at [email protected]
Pass/Fail: |
---|
Comments: |
---|
Student Signature: | Date | ||
---|---|---|---|
Certifier Signature: | Date |
Certifer: Please scan this QR Code to email info@claremontmakerspace.org, and include a list of students who have passed this test.
Then, return this form to the front desk (even if the student failed!).